Professional Web Applications Themes

how to config this on a debian box ???? - Linux Setup, Configuration & Administration

hi all i just install an 100fiber card, i just do not know how to config,please help i had enclose the demsg output: the card i want to install is eth0 Cogent EM100' board. thks!! john Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide2: ports already in use, skipping probe Floppy drive(s): fd0 is 1.44M FDC 0 is an 82078. loop: loaded (max 8 devices) Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001) tulip0: Old format EEPROM on 'Cogent EM100' board. Using substitute media control info. tulip0: EEPROM default ...

  1. #1

    Default how to config this on a debian box ????

    hi all

    i just install an 100fiber card, i just do not know how to
    config,please help
    i had enclose the demsg output:

    the card i want to install is eth0 Cogent EM100' board.

    thks!!
    john

    Uniform Multi-Platform E-IDE driver Revision: 6.31
    ide: Assuming 33MHz system bus speed for PIO modes; override with
    idebus=xx
    ide2: ports already in use, skipping probe
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is an 82078.
    loop: loaded (max 8 devices)
    Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
    tulip0: Old format EEPROM on 'Cogent EM100' board. Using substitute
    media control info.
    tulip0: EEPROM default media type Autosense.
    tulip0: Index #0 - Media 100baseFx (#7) described by a 21140 non-MII
    (0) block.
    tulip0: Index #1 - Media 100baseFx-FDX (#8) described by a 21140
    non-MII (0) block.
    tulip0: Index #2 - Media 10baseT (#0) described by a 21140 non-MII
    (0) block.
    tulip0: Index #3 - Media 10baseT-FDX (#4) described by a 21140
    non-MII (0) block.
    tulip0: Index #4 - Media 100baseTx (#3) described by a 21140 non-MII
    (0) block.
    tulip0: Index #5 - Media 100baseTx-FDX (#5) described by a 21140
    non-MII (0) block.
    eth0: Digital DS21140 Tulip rev 32 at 0xfc80, 00:00:92:97:10:10, IRQ
    12.
    SCSI subsystem driver Revision: 1.00
    sim710: No NCR53C710 adapter found.
    ahc_pci:1:11:0: Using left over BIOS settings
    ahc_pci:1:12:0: Using left over BIOS settings
    scsi0 : Adaptec AIC7 EISA/VLB/PCI SCSI HBA DRIVER,
    JOHN Guest

  2. #2

    Default Re: how to config this on a debian box ????

    On Sun, 18 Jan 2004 07:28:36 -0800, JOHN wrote:
     

    you do realise you need more then one card to work with fddi ?
    you also need to compile your kernel to support fddi statically or as a
    module.

    --
    Best Regards,

    Dr. Chandra

    Dr. Guest

  3. #3

    Default Re: how to config this on a debian box ????

    On 18 Jan 2004 07:28:36 -0800, JOHN
    <com.hk> wrote: 

    Apparently you have already configured the correct module for this
    card. To set the IP address and netmask, edit /etc/network/interfaces
    (man 5 interfaces).


    --
    Absurd Procrustean Egghead Cornstarch Variant Bill Mar
    Bill Guest

Similar Threads

  1. Replies: 3
    Last Post: June 1st, 02:49 AM
  2. Replies: 6
    Last Post: October 31st, 02:34 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139